Third-generation PCE superplasticizer in flake and powder form — 97.0% min solids, completely water-soluble, up to 35% water reduction. For concrete, dry-mix mortar, self-levelling, tile adhesives and oil-well cementing. Manufactured and tested in-house, shipped worldwide.
PCE superplasticizer is the third generation of water-reducing agents — evolved from lignosulfonate and naphthalene types. In flake and powder form it disperses cement and mortar particles more effectively, so you use less water and less binder without giving up workability.
97.0 ± 1.0% solids in every bag — completely water-soluble. Dissolve to a 10% or 20% solution for ready-mix concrete and mortar dosing.
Lower water-cement ratio means higher strength and denser concrete — water reduction ratio tested at ≥ 25%, up to 35% on P.O 42.5 cement.
CL2618 stays effective to 60 °C and the rest to 50 °C — built for hot climates, warm storage and demanding mixing conditions.
Chloride ≤ 0.02% and total alkali ≤ 0.3% keep reinforcement safe — suited to reinforced and prestressed concrete.
Recommended dosage is only 0.1–0.6% of cementitious weight. A little goes a long way — each 25 kg bag covers far more mortar or concrete than conventional admixtures.
Flakes for water-reducing and slump-retention concrete, powders for dry-mix mortar, self-levelling and tile adhesives. Pick the form that suits your plant.
Flakes and powders with 97% min solids, ISO-certified and batch-tested in our own lab. Choose by form and priority: water reduction, slump retention, dry-mix mortar or heat resistance.
Water reducing
High-performance PCE flake with water-reduction ratio up to 35%. Completely water-soluble, eco-friendly, made from EPEG 912.
Slump retention
Slump-retention PCE flake that keeps concrete fluid and cohesive over long hauls and hot weather, without segregation.
Dry-mix mortar
Fully water-soluble PCE powder for dry-mix mortar and concrete — gypsum- and cement-based systems, self-levelling, plaster, grouts and adhesives.
Heat stable 60 °C
Heat-resistant PCE powder with excellent early strength, optimized for construction chemicals, self-levelling screeds and oil-well cementing.
| Grade | Form | Solid | Water reduction | Dosage | Best for |
|---|---|---|---|---|---|
| CL-2628 | Flake | 97% | ≥ 25% (up to 35%) | 0.1–0.5% | Ready-mix, precast, high-strength concrete |
| CL-2645 | Flake | 97% | ≥ 25% | 0.1–0.5% | Long slump retention, hot weather |
| CL-2621 | Powder | 97% | ≥ 25% | 0.1–0.5% | Dry-mix mortar, self-levelling, tile adhesives |
| CL-2618 | Powder | 97% | ≥ 25% | 0.1–0.6% | Heat-resistant mortar, screeds, oil-well cement |
Packaging: 25 kg plastic woven bags with PE inner liner · 14–16 t per 20'GP · 27 t per 40'HC — customized packaging available on request.
CL-2628Flake · Water reducing
CL-2628Flake form
CL-2645Flake · Slump retention
CL-2645Flake form
CL-2621Powder · Fully water-soluble
CL-2621Powder form
CL-2618Powder · Heat resistant
CL-2618Powder form
Each grade links to its full datasheet on our official site.
Published figures below are from our product datasheets for the powder & flake grades. Every batch is tested in our own laboratory; independent SGS testing per GB 8076-2008 is available on request.
| Property (typical, CL-2628 flake) | Value |
|---|---|
| Appearance | White or light yellow flake |
| Bulk density | 450 ± 50 kg/m³ |
| Solid content | 97.0 ± 1.0% |
| pH value | 5 – 7 |
| Moisture content | ≤ 3.0% |
| Water reduction ratio | ≥ 25% (up to 35%) |
| Chloride content (Cl⁻) | ≤ 0.02% |
| Total alkali content | ≤ 0.3% |
| Property (typical, CL-2621 powder) | Value |
|---|---|
| Appearance | White or light yellow powder |
| Bulk density | 500 ± 50 kg/m³ |
| Solid content | 97.0 ± 1.0% |
| pH value | 5 – 7 |
| Moisture content | ≤ 3.0% |
| Water reduction ratio | ≥ 25% |
| Chloride content (Cl⁻) | ≤ 0.02% |
| Total alkali content | ≤ 0.3% |
| Max working temperature | 50 °C (CL-2618: 60 °C) |
| Usage & handling | Guideline |
|---|---|
| Recommended dosage | 0.1–0.5% of cementitious materials by weight (CL-2618: 0.1–0.6%) — confirm by mix design test |
| How to dose | Dissolve flake or powder in water to a 10% or 20% solution before use in ready-mix concrete |
| Compatibility | Do not mix with naphthalene sulphonate; run compatibility tests when used with other admixtures |
| Storage | Store dry below 40 °C, no stacking or heavy pressure to avoid caking |
| Shelf life | 12 months unopened — use within 60 days after opening |
Non-toxic, non-irritating, non-combustible. Transported as general chemical products. Full COA and MSDS supplied with every shipment.
From dry-mix mortar plants to ready-mix concrete, from self-levelling screeds to oil-well cementing — one supplier covers the whole mix design.
Binzhou Chengli Building Materials Co., Ltd. is a Chinese manufacturer specializing in concrete admixtures — production, R&D and export under one roof since 2012.
ISO 9001 quality, ISO 14001 environmental and ISO 45001 occupational health & safety management — valid through 2028.
Independent SGS testing per GB 8076-2008 confirms solid content, pH, alkali and chloride levels — shareable on request.
Complete production lines plus a chemical-analysis and physical-property laboratory built with Shandong University.
Incoming raw materials are inspected and every index recorded; production is controlled end-to-end so every drum performs like the last.
200 kg drums, 1000 L IBC tanks and 23 t flexitanks; packaging can be customized to your port, pallet or labeling needs.
Tell us your cement, aggregates and target slump or strength — our lab will recommend the grade and dosage before you order.
Certificates and test reports are available for your compliance review.
ISO-certified management systems, plus invention and utility-model patents covering our admixture formulations and production equipment.
ISO 9001 · Quality Management
ISO 14001 · Environmental Management
ISO 45001 · Occupational Health & Safety
Invention Patent · Retarding admixture
Utility Patent · Uniform mixing device
Utility Patent · Auto dosing device
Utility Patent · Feeding equipment
Utility Patent · Cooling unit
Utility Patent · Stirring device
Utility Patent · Concrete mixer
Utility Patent · Blending equipment
Utility Patent · Ball-milling unit
Yes — samples are available on request. Send us your contact and application details through the form or WhatsApp, and we will arrange a sample with the datasheet for the grade that fits your mix.
CL-2628 and CL-2645 are flake grades for water reduction and slump retention in concrete; CL-2621 and CL-2618 are powder grades for dry-mix mortar, self-levelling and heat-resistant applications. All are 97% min solids and completely water-soluble — dissolve to a 10% or 20% solution before use in ready-mix concrete.
Use CL-2628 for standard and high-strength concrete, CL-2645 when you need long slump retention for hauls or hot weather, CL-2621 for dry-mix mortar and self-levelling systems, and CL-2618 when you need heat resistance or oil-well cementing performance. Our technical team can recommend the right grade and dosage for your materials.
Typically 0.1–0.5% of cementitious materials by weight (0.1–0.6% for CL-2618), depending on the grade, target performance and materials. Always run a compatibility and dosage trial with your own cement or dry-mix formula; our lab can support the mix design.
Store in a dry place below 40 °C without stacking or heavy pressure to avoid caking. Shelf life is 12 months in the original package; use within 60 days after opening. The product is non-toxic, non-irritating and non-combustible.
Standard export packaging is 25 kg plastic woven bags with PE inner liner — about 14–16 t per 20'GP and 27 t per 40'HC with pallets. Packaging can be customized to your port, pallet and labeling needs; MOQ and lead time depend on grade and destination — we confirm within one working day.
Tell us your application, grade and quantity. A factory sales engineer will reply within one working day with pricing, datasheets and shipping options.
Fields marked * are required. We reply within one working day.
Binzhou Chengli Building Materials